當前位置：南京科耐特機械環?？萍加邢薰?/a>>>曝氣機>>AP潛水離心曝氣機

AP潛水離心曝氣機

返回列表頁

參考價

面議

具體成交價以合同協議為準

產品型號

品牌

廠商性質其他

所在地

在線詢價 收藏產品查看聯系電話

聯系方式：查看聯系方式

更新時間：2023-05-16 18:00:46瀏覽次數：359次

聯系我時，請告知來自環保在線

產品分類 品牌分類

  曝氣機

全部產品列表

暫無信息

南京科耐特機械環?？萍加邢薰?/a>

經營模式：其他

商鋪產品：13條

所在地區：

詢價 給他留言

產品簡介

AP(QXBL) 型潛水離心曝氣機 AP(QXBL) Centrifugal Submerged Aerator 用途 Applications AP(QXBL)型離心式潛水曝氣機用于污水處理廠曝氣池、曝氣沉砂池中，對污水的混合液進行充氧及混合，以及對污水

詳細介紹

AP(QXBL)型潛水離心曝氣機
AP(QXBL) Centrifugal Submerged Aerator
用途 Applications
AP(QXBL)型離心式潛水曝氣機用于污水處理廠曝氣池、曝氣沉砂池中，對污水的混合液進行充氧及混合，以及對污水進行生化處理或養殖塘增氧。進氣量為 10-320m3/h，增氧能力為 0.37-24kgO2/h，電機功率 0.75-22kw。
The type AP( QXBL) centrifugal submerged aerator is used for the aerating ditch and sａnd removed ditch in the wastewater treatment plant, and oxygenating and mixing liquid, andhad biochemical treatment or aerated the oxidation ditch. The amount of entering air is 10-320m3/h, the ability of oxygenation is 0.37-24kgO2/h, the power of motor is 0.75-
22kw.
型號表示方法 Model
AP(QXBL) -
┃        ┃
┃            ┃
┗━━ 電機功率 POWER (KW)
                                                    ┃
                                                    ┗━━━━━━━━ 離心式潛水曝氣機 TYPE AP(QXB) CENTRIFUGAL SUBMERGED AERATOR
特點 Features
1. 結構緊湊、占地面積小、安裝方便；
2. 除吸氣口外，其余部分潛入水中運行，噪音小；
3. 吸入空氣多，產生氣泡多而細，容氧率高；
4. 無需提供氣源，省去鼓風機，工程投資少；
5. 結構采用新的技術設計，整機重量輕，運行安全可靠。
1. Well-knit structure, less lａnd occupation, convenient installation;
2. The other parts operated below the water except the inlet, the yawp was small;
3. The air inbreathed was much, produced the bubble much and close, and the rate of oxygenwas high;
4. Provided the air without headstream, left out the blower, and the cost of projece
was low;
5. Instruction was designed by the new technology method with light and portable, and operated safe and reliably.
構造及工作過程 Structure and working process
潛水曝氣機由潛水射流泵、混合室、底座、進氣管和消音器等組成。進氣管上端為空氣吸入位于水面之上，下端與混合室聯通，接通電源后由于葉輪旋轉，水流從葉輪的出口流出經混合室使之形成負壓，因而空氣被吸入并與液體混合，混合液從周邊流出，完成對液體的充氧。
The submerged aerator is composed of submerged pump, mixing room, the seat, inlet pipe, muffle and so on.
The top of inlet pipe was above the surface of water, the underside was connected with mixing room, because the impeller had circumgyrated after the power supply was turn on, the high-speed water poured through the mixing room, and formed the negative pressure, the air was inhaled into and mixed with liquid. The mixed liquid poured from the side, and achieved the oxygenation to liquid.
主要性能參數 Main Performance Parameters
潛水離心曝氣機可在下列條件下正常連續運行：
1. 介質溫度不超過40℃
2. 介質的PH 值在 5~9
3. 介質密度不超過 1150kg/m3
The submerged aerator functions continuous at the following conditions:
1. The temperature not exceeding 40℃
2. The PH value 5~9 in the medium
3. medium density not exceeding 1150kg/m3

電氣控制 Electrical control
按手動配置控制箱，接入曝氣機熱保和漏?？刂凭€，可帶 PLC 接口，亦可按用戶要求配置。
D-QXB-I 控制箱適用于電源為三相 380V、頻率 50Hz，控制潛水曝氣機的起停，可以通過 PLC 接口潛水曝氣機運行的自動控制系統。并具有過載、短路、缺相、泄露、過熱等保護功能。
Configure the manual controller, could have the PLC interface, could configure according to customer’s demands.

外形尺寸 Diensions



工作實例 Working Example