FeaturesForm Factor: Hot-pluggable OSFP800 form factorData Rate: Aggregate data rate of 850 Gb/s and Breakout data rate of 106.25 Gb/sOptical Interface: Compliant to 2×400GBASE-DR4 and 8x10......

詳細(xì)介紹

OSFP 800G DR8 SM MPO12 IB Transceiver

NVIDIA twin port transceiver
800G ,2xNDR, OSFP, 2xMPO12 APC, 1310nm SMF, up to 100m, finned.

Functional Block Diagram

800G OSFP DR8

General Description

The 800G OSFP DR8 are high-performance, cost-effective transceivers designed for utilization in 800 Gigabit Ethernet links over 500 meters. On transmitter side, the module converts eight channels of 53.125 GBaud (PAM4) electrical data to eight channels of parallel optical signals with data rate of 53.125 GBaud (PAM4). At receiver side, the module converts eight channels of parallel optical signals with data rate of 53.125 GBaud (PAM4) into eight channels of 53.125 GBaud(PAM4) electrical output data.

The product is designed according to the OSFP MSA. It is designed to meet the harshest external operating conditions including temperature, humidity and EMI interference.

Absolute Maximum Ratings and Recommended Operating Conditions

Absolute Maximum Ratings

Parameter	Symbol	Min	Typical	Max	Unit
Storage Temperature	Ts	-40		85	°C
Relative Humidity (non-condensation)	RH	15		85	%
Supply Voltage	Vcc	-0.5		3.6	V
Optical Input Power, per Lane	PIN			5.0	dBm

Recommended Operating Conditions

Parameter	Symbol	Min		Max	Unit
Operating Case Temperature	TC	0		70	°C
Signaling Rate, each lane			53.125		GBd
Data Rate Accuracy		-100		100	ppm
Power Supply Voltage	VCC	3.135	3.3	3.465	V
Pre-FEC Bit Error Ratio				2.4E-4
Transmission Distance				500	m

Optical Specifications

Optical Transmitter

Transmitter optical characteristics

Parameter	Symbol	Min	Typical	Max	Unit
Signaling rate, each lane	SR	53.125+/-100ppm			GBd
Modulation format		PAM4
Lane wavelength	λ	1304.5	1311.0	1317.5	nm
Side-mode suppression ratio	SMSR	30			dB
Average launch power, each lane^a	AOPTX	-2.9		4.0	dBm
Outer Optical Modulation Amplitude (OMAouter), each lane^b	OMATX	-0.8			dBm
Launch power in OMAouter minus TDECQ, each lane		-2.2			dBm
Transmitter and dispersion eye closure for PAM4, each lane	TDECQ			3.4	dB
Average launch power of OFF transmitter, each lane	AOPOFF			-15	dBm
Extinction ratio, each lane	ER	3.5			dB
RIN21.4OMA				–136	dB/Hz
Optical return loss tolerance	RLTol			21.4	dB
Transmitter reflectance^c	Reflectance_ Tx			-26	dB

Note:

a. Average launch power, each lane (min) is informative and not the principal indicator of signal strength. A transmitter with launch power below this value cannot be compliant; however, a value above this does not ensure compliance.

b. Even if the TDECQ < 1.4 dB, the OMAouter (min) must exceed these values.

c. Transmitter reflectance is defined looking into the transmitter.

3.2 Optical Receiver

Receiver optical characteristics

Parameter		Symbol	Min	Typical	Max	Unit
Signaling rate, each lane		SR	53.125+/-100ppm			GBd
Modulation format			PAM4			-
Lane wavelengths		λ	1304.5	1311.0	1317.5	nm
Damage threshold, each lane^a		DThd	5			dBm
Average receive power, each lane^b		AOPRX	-5.9		4	dBm
Receiver reflectance		Reflectance_ Rx			-26	dB
Receiver sensitivity (OMAouter), each lane^c		RxSens			-4.4	dBm
Stressed receiver sensitivity (OMAouter), each lane^d		SRS			-1.9	dBm
Conditions of stressed receiver sensitivity test:^e
Stressed eye closure for PAM4 (SECQ), lane under test				3.4		dB
OMAouter of each aggressor lane				4.2		dBm
Rx LOS	LOS Assert	LOSA	-15		-7.9	dBm
	LOS De-assert	LOSD			-7.4	dBm
	LOS Hysteresis	LOSH	0.5		5	dB

Notes:

a. The receiver shall be able to tolerate, without damage, continuous exposure to an optical input signal having this average power level. The receiver does not have to operate correctly at this input power.

b. Average receive power, each lane (min) is informative and not the principal indicator of signal strength. A received power below this value cannot be compliant; however, a value above this does not ensure compliance.

c. Receiver sensitivity (OMAouter), each lane (max) is informative and is defined for a transmitter with SECQ of 0.9 dB.

d. Measured with conformance test signal at TP3 for the BER = 2.4E-4.

e. These test conditions are for measuring stressed receiver sensitivity. They are not characteristics of the receiver.

Digital Diagnostic Monitor Accuracy

The following characteristics are defined over recommended operating conditions.

Parameter	Accuracy	Unit
Internally Measured Transceiver Temperature	+/-3	℃
Internally Measured Transceiver Supply Voltage	+/-3	%
Measured Tx Bias Current	+/-10	%
Measured Tx Output Power	+/-3	dB
Measured Rx Received Average Optical Power	+/-3	dB