Main features:
主要特點
? Open type vertical heating furnace,tube and flange can pivot and move away from chamber.
開啟式立式加熱體，爐管法蘭可繞軸旋轉移出爐腔。
? With standard configuration of OD60mm quartz tube and 20T electrical press
標配Φ60mm石英管真空密封，20T電動壓力機。
? Adopt graphite push rod and mould,at the same time of pressing,heat the powder to common sintering temperature or lower,to get the dender and uniform product after a short time
采用石墨頂桿和石墨模具，在加壓的同時使粉末加熱到正常燒結溫度或更低一些，經過較短時間燒結成致密而均勻的制品。
Technical Parameters
技術參數
Power 輸入電源 | · Power rated: 2KW · 額定功率：2KW |
Voltage 電壓 | · Voltage rated: AC220V 50/60HZ · 額定電壓： AC220V 50/60HZ |
Working Temperature 工作溫度 | · Max. Temperature: 1200 °C ( 1 hr) Z高溫度：1200℃ (1小時) · Continuous working temperature: ≤1150℃ 持續工作溫度：≤1150℃ · Max. heating Rate: ≤10°C /min Z快升溫速率：≤10℃/分 |
控溫方式 | · PID automatic control and auto-tune function. 模糊PID控制和自整定調節 · 30 programmable segments for precise thermal processing. 智能化30段可編程控制 · Built-in protection for the over-heated and broken thermocouple. 超溫和斷偶報警功能 |
Heating Elements 加熱元件 | · Resistance wire, Fe-Cr-Al Alloy doped by Mo · 電阻絲（摻鉬鐵鉻鋁合金） |
Temperature Accuracy 控溫精度 | +/- 1 °C |
Prosessing tube 爐管 | · Φ60*350mm
|
Graphite rod diameter 石墨壓桿直徑 | 48mm |
Pressure maintain time 保壓時間 | 0-50min |
Movable distance 壓力行程 | 50mm |
Plunger diameter 活塞直徑 | 87 mm |
Pressure stability 壓力穩定性 | ≤1MPa/5min |
Weight 重量 | 300kg |
真空法蘭 | · Special designed flanges 定制法蘭
|
Vacuum Pressure 真空壓力 | · 133torr can be achieved by mechanical pump 機械泵可達133torr（1pa） · 10^-6 torr can be reached by molecular pump 分子泵可達10^-6torr（10^-3pa） · Please click the picture below to order vacuum parts 點擊下列圖片訂購真空部件
|
Warranty 質保 | One year limited warranty with lifetime support (Such consumable parts as tO-rings, etc. are NOT supported by the warranty) 一年質保終身支持（消耗品如O型圈等不在質保范圍內） |
Warning 注意事項 | · Graphite must used under anaerobic condition 石墨必須絕氧使用 · Considering contact area calculate pressure 計算壓強時應考慮接觸面積 · Small cracks may appear on the surface of the refractory ceramics over extended use. This is a normal occurrence and the cracks may be repaired with alumina coating. 在使用過程中爐膛表面可能出現細小裂紋。這是正常情況，裂紋可以用氧化鋁涂層修復。
|
Compliance 認證 | · CE Certified CE認證 · The furnace is ready to pass TUV (UL61010) or CSA certification at extra cost. 可付費進行TUV(UL61010)或CSA認證 |
Operation instructions 操作指導 | · Click to download the operating manual · 點擊下載說明書
|
環保在線