騰達試驗儀器廠：
一、產品簡介：
依據行業標準JC482-485-92設計制造的流平性模適用于建筑密封膏的流平性試驗取樣用。150×20×15mm流平性試模流平性模具下垂度試模建筑密封材料流平性模具。
the product introduction:
The leveling mold designed and manufactured according to the industry standard JC482-485-92 is suitable for the sampling of the leveling test of building sealing paste.150×20×15mm leveling test mold Leveling mold sag test pattern Building sealing material leveling mold.
二、使用方法：
★將試料和模具在5±2oC的低溫線內放置30min。
★再模具內襯以0.1mm左右的油紙，油紙四周翻邊到模具外，內襯油紙要展平。
★沿模具的一端到另一端注入約20ml的試料，在5±2oC溫度下靜止放置1h，觀察其表面是否平整光滑。
Second,the method of use:
★Place the sample and mold in a low temperature line of 5±2oC for 30min.
★The inner lining of the mold is about 0.1mm oil paper,the oil paper is turned around the mold,ａnd the inner lining oil paper is flattened.
★Inject about 20ml of sample along one end of the mold to the other end,ａnd stａnd it at 5±2oC for 1h,ａnd observe whether the surface is smooth and smooth.
三、器具構成：
本器具主要由內部尺寸為150*20*15mm的槽體構成。
Third,the appliance composition:
The appliance is mainly composed of a tank having an inner size of 150*20*15 mm.
四、建筑密封材料檢測用下垂度試模膠下垂度試模流平性模具
200mm*20mm*10mm
不銹鋼鋁制
下垂度模具：長度（150±0.2）mm兩端開口，其中一端底面延伸（50±0.5）mm，槽的橫截面內部尺寸和寬（20±0.2）mm，深（10±0.2）mm。
150*20mm下垂度模具下垂度試模流平性試模下垂度試模掛架建筑密封材料檢測用下垂度試模
無氣孔且光滑的槽型模具，宜用陽極氧化或非陽極氧化鋁合金制成，長度150mm正負0.2mm，兩端開口，其中一端底面延伸50mm正負0.5mm，槽的橫截面內部尺寸為寬20mm正負0.2mm，深10mm正負0.2mm，其他尺寸的模具也可以實用例如10正負0.2mm，深10正負0.2mm。
Fourth,the construction of sealing materials testing sag test mode rubber sag test mold leveling mold
200mm*20mm*10mm
Stainless steel
Sag mold:length(150±0.2)mm open at both ends,one end of the bottom extends(50±0.5)mm,the internal dimensions of the cross section of the groove and width(20±0.2)mm,deep(10±0.2)mm.
150*20mm sag mold sag test slab leveling test sag sag test slab sag test sag
Non-porous and smooth grooved mold,should be made of anodized or non-anodized aluminum alloy,length 150mm plus or minus 0.2mm,open at both ends,one end of the bottom surface extends 50mm plus or minus 0.5mm,the inner dimension of the cross section of the groove is Width 20mm plus or minus 0.2mm,depth 10mm plus or minus 0.2mm,other sizes of mold can also be practical,for example,10 plus or minus 0.2mm,depth 10 plus or minus 0.2mm.
五、注意事項：
使用完畢后用溶劑擦干凈，并干燥后進行保存。
Fourth,note:
After use,wipe with a solvent and dry before storing.
六、裝箱單：
1、流平性模6個
2、說明書1本
3、合格證1張
Five,packing list:
1,leveling mold 6
2,the manual 1
3.Certificate 1
